biomass materials for pellets Archives - Cina Produttore di linee di pellet per macchine a pellet

18 Common Biomass Materials For Pellets and Pellets Calorific Value Biomass pellets are the most used fuel for heating, cooking and electricity generation. They are made from renewable resources such as wood, straw and agricultural waste. The biomass pellet is a good alternative to fossil fuels as they provide clean energy with low CO2 emissions. Biomass pellets can be used in both residential and commercial applications such as biomass boilers, wood-fired boilers, stoves, fireplaces and pellet stoves. They are also used in power plants which generate electricity from renewable sources of energy such as wind turbines or solar panels. Here we will show you're the common biomass pellets for pellets and their pellets caloric value. Different Biomass Materials for Pellets Wood Materials Waste wood chips, shavings from board factories and furniture factories, waste sawdust and trimmings from logging sites, construction panel waste, garden pruning, mountain forest logs, etc. Bamboo Materials Bamboo craft waste, such as chopsticks, toothpick factory waste, etc. Straw Grasses Cotton stalks, corn stalks, soybean stalks, rapeseed stalks, wheat stalks, rice stalks, cassava stalks, bagasse, tobacco stalks, sea buckthorn stalks and other herbaceous plant stalks; energy grass, giant king grass, alfalfa grass (mainly used as feed for cattle and sheep) Other Materials for Pellets Rice husk, peanut husk; sugarcane bagasse, palm silk, coconut husk, tea seed husk, cow dung, fruit residue, etc. Biomass Pellets Manufacturing Process The manufacturing of biomass pellets consists of multiple steps including raw material pre-treatment, pelletizing section and final treatment process. The pre-treatment process means processing your materials into small size 3-5mm, this process include crushing and drying if needed. Because for making pellets you must make sure your material moisture 10-15%. Pelletizing section means pressing the ready materials into biomass pellets. The materials will be fed into the pelletizing room, they will fed between the roller and die and will be pressed time and time by the rotating roller, the temperature will change the Lignin and fiber content of the material, make them soft of and subsequent increase in adhesion, finally the shaped pellets will be pushed out from the die hole and cut by the outer rotating knife. The final treatment process include the cooling and packing of final pellets. To make the pellets easy and longer time for storage, these steps are essential. Different Pellets Calorific Value The type of biomass material will determine the pellets calorific value, we made a summary of the calorific value of pellet fuel: the calorific value of agricultural raw material pellet fuel is generally around 3000-4200kcal/kg, the calorific value of forestry raw material pellet fuel is generally higher at around 4200-5000kcal/kg, the calorific value of forestry type pellet fuel is not less than 7000kcal/kg after carbonization. Differents Pellets Calorific Value Weed Pellets Calorific Value 3873kcal/kg Rice Husk Pellets Calorific Value 3828kcal/kg Rice Straw Pellets Calorific Value 4215kcal/kg Corn Stalk Pellets Calorific Value 4241kcal/kg Corn Cob Calorific Value 4238kcal/kg Wheat Straw Pellets Calorific Value 4428kcal/kg Peanut Shells Calorific Value 5119kcal/kg Chinese Fir Pellets Calorific Value 4587kcal/kg Pine Wood Pellets Calorific Value 4552kcal/kg Poplar Pellets Calorific Value 4286kcal/kg Cow Dung Pellets Calorific Value 2779kcal/kg Firewood Pellets Calorific Value 4003kcal/kg Tree Leaf Pellets 3502kcal/kg Bean Pole Pellets Calorific Value 3862kcal/kg Sorghum Stalk Pellets Calorific Value 3601kcal/kg Sophora Stick Calorific Value 4323kcal/kg Wood Chips Pellets Calorific Value 4401kcal/kg Furfural Residue Calorific Value 3145kcal/kg Factors Affecting Pellet Quality 1、Type of Raw Materials Different kinds of raw materials, its pelletizing process are quite different, among the large quantity agricultural and forestry waste, some are much easier to shape into pellets after crushing, but some are quite difficult. The type of raw materials will affect the quality of pellets forming, such as the density, strength, calorific value of wood pellets, etc., and also has a certain impact on the output and power consumption of biomass pellet mill. 2、Raw Material Size The raw material particle size is also an important factor affecting the pellet forming. Generally speaking, the finer the size of raw materials, the higher pellets strength will be, but it is not suitable for adjusting humidity and easy to agglomerate bonding. And also if the crushed raw materials too fine, this will result in high energy consumption of crushing. If raw material particle size is too coarse, this will increase the wear and tear of the die and pressure roller, pellets forming much more difficult, especially for the small diameter die, this will cause the material softening paste effect poor and result in high material consumption, low yield, the output of final pellets will also contain high powder rate. The following are the results of the different size materials pellets forming based on our test, we are taking the corn straw as material, with most suitable ring die compression ratio, most suitable moisture content and final pellets diameter 8mm, please check the final result below : Particle Size Range(mm) Density(ton / m3) 0~1 1.13 1~5 1.25 5~10 1.01 >10 0.79 3、Moisture Content of Raw Materials When the moisture content of raw materials too low, the friction between raw materials will limit the sliding and extension, so the combination of raw materials is not close enough, pellets forming will not firm or even difficult to shape; when the moisture content of raw materials too high, although the flow of raw material particles is good, can be fully extended, and mutual engagement, but the excess water will be extruded from the raw materials, distributed between the raw materials, raw materials between the particles will difficult to closely fit, will also cause forming is not firm, or even difficult to shape. The humidity required to produce pellets is different for different raw materials, subject to temperature and other factors, most of the raw material humidity required is 8% to 15%, but there are some special materials need higher humidity, such as teak wood need even up to 50%, etc., It's better to pre-test them before making pellets because this will affect the final pellets quality. For excessive humidity of the raw materials must be processed to reduce moisture before pelletizing, usually through the drying process. 4. Forming Pressure Forming pressure is the most basic condition of material pellets forming. Only with sufficient pressure, the raw material can be compressed into pellets. However, the pressing pressure is closely related to the shape and size of the ring die. If ring die compression ratio is too small, the effective length of the die hole is short, the material in the ring die hole pressing pressure is small, they will be easily to squeeze out the ring die, although the yield is high but the final pellets will be loose and the appearance is not smooth; If ring die compression ratio is too large, the effective length of the die hole is long, the greater the pressure of the material in the die hole, the final pellets density is higher, the pellets is smooth and good quality, however the output of the pellet mill will be reduced and the cost of the pelletizing will be increased accordingly. The following is the corn stalk pelletizing result with different ring die compression ratio for your reference : Compression Ratio Density(ton / m3) Production Capacity(kgs/h) Power Consumption(kw*h/t) 3.5 0.91 500 64 4 1.05 780 46.21 4.5 1.21 900 46.78 5 1.23 800 54.23 5.5 1.22 650 71.32 Conclusion In the actual biomass pellets production process, the nature of raw materials, pre-treatment methods, equipment parameters, etc. are interacting with each other, so it is also necessary to consider the unit energy consumption, production rate, maintenance and production cost, etc., Combine them with actual statistics to come up with the most ideal pelletizing procedure, then you can produce the best strength and durability biomass pellet fuel. Talk to An Expert SHARE THIS POST Facebook Twitter LinkedIn